Factory price manual curved screen printing machine for cups,Glass tube, pen, fishing rod, bat

 This machine is mainly used for cylindrical type, cone type products;Such as a variety of plastic, glass, metal materials made of cylindrical, conical shape products, including wine bottles, medicine bottles, cosmetics bottles and other packaging bottles;Mugs, vacuum cups, beer glasses, wine glasses and other cups;Glass tube, pen, ballpoint pen, fishing rod, bat and other small cylindrical products.

For cylindrical and conical products, the printing surface has a large depression or convex, and the printing surface has pitting and other non-planar printing is not suitable for this machine.

Curved screen printing machine is mainly used for cylinder type and cone type products with diameter below 170 mm

1, the machine adopts left and right push-pull structure;The installation can be adjusted according to the need, suitable for left or right hand convenient operation;Suitable for printing height of 200 mm;Patterns within 150 mm in length;It is suitable for the use of all kinds of screen panels with outer diameter of 260*450 mm and thickness of 35 mm.

2, this machine for the rear main frame height adjustment and positioning, the rear main beam according to the substrate height, by adjusting the column screw screw to adjust up and down.The upper and lower adjustment range is 200mm.Cylindrical and conical products with a diameter of 170 mm can be printed.

3.The substrate printing frame can be left and right, front and back mobile design, the bottom of the three fixed aluminum bars directly installed on the base, the installation of aluminum bars can move about 290 mm;On both sides of the substrate placement frame installation strip, the middle for the substrate positioning frame installation strip.The three mounting strips can be moved left and right according to the need, and the clamp is placed in the 19 U-shaped holes before and after the base (each hole spacing is 15mm), to ensure the accurate positioning of the mounting strips.

Shift of the installation strip: loosen the screws at both ends of the installation strip, push the installation strip to the long strip hole at the rear of the machine, move the installation strip left and right to the appropriate position, pull the installation strip to the fixed U-shaped slot, and tighten the screws at both ends to complete the positioning.

4.Three sets of substrate are used to place the rollers, which are metal bearing rollers (diameter 19 mm) respectively;Nylon bearing roller (diameter 25 mm);Plastic bearing roller (diameter 50 mm), user can replace according to need.Three types of rollers can be installed on the main rack and accessory rack.Bearing mounting frame is directly fixed in the aluminum strip mounting hole, according to the height of the substrate can be moved back and forth up to 160 mm;

4 additional mounting frames, remove the bearings of the original main mounting frame, and directly fix the additional mounting frames on the main mounting frame with screws, which is mainly used for printing of tapered products.Additional mounting rack can be moved up and down 20 mm.

5.The net plate is installed with a two-way fixed type, and the upper handle is fixed to the net frame;The middle baffle of the chuck shall be adjusted according to the width of the screen frame, and the two handles shall be fixed firmly after being attached to the inside of the screen frame. It is suitable for all types of screens of height, width 10-35 mm.

6, the mesh support seat is mainly used to support the placement of the mesh after printing, to prevent the mesh from falling in the hand;The support seat can be adjusted up and down according to the thickness of the mesh plate to fit the best support.

7.Mesh frame is equipped with a special handle directly fixed on the mesh frame, two installation methods, can be installed in the upper part of the mesh frame, can also be installed on the side of the mesh plate, the left and right push and pull convenient and fast, the handle can be arbitrarily fixed in any part of the mesh frame, the upper red handle and the front baffle fixed mesh plate, ensure that the mesh plate is firmly fixed on the handle.The handle is suitable for all kinds of mesh frames within the thickness and width of 35 mm.

8.The scraper frame is used to fix the wooden handle scraper with self-tapping, suitable for the wooden handle scraper with the length of 200 mm.The frame can be moved around 250 mm according to the position of the screen pattern

9.Net plate moving distance positioning;Positioning ring and anti-impact apron are provided on both sides of the optical axis. The positioning ring can be adjusted left and right to reach the appropriate position according to the size of the pattern.Anti-impact apron can prevent the abnormal sound from the collision between metals and protect the machine components.

The machine can be adjusted by three parts to complete the implementation of the main operation of the left hand;Adjust the handle of the mesh frame;Adjust the position of the sliding block bearing;Adjust three parts such as the support seat of the mesh plate can be completed.

XI. Usage (for reference only)

1. Install the mesh plate and adjust the lower support seat of the mesh plate to the basic level of the mesh plate;Install the screen frame pull handle;

2. Install the scraper and adjust the distance of the scraper from the pattern to be fixed at 1-2 cm;

3, adjust the position of the substrate printing frame and the roller bearing, place the substrate, the spacing between the top of the substrate and the screen plate is 1-3 mm;And the top of the substrate is aligned with the bottom of the scraper;

4, according to the pattern of the left and right size to adjust the plate distance positioning knob;

5, the screen into the ink;

6, left hand (or right hand) hold the scraper;The right hand (or left hand) pull the handle on the screen frame can be printed.